DIAGNOSING A WATER HEATER FAILURE: WHAT TO DO WHEN IT CEASES WORKING

Diagnosing a Water Heater Failure: What to Do When It Ceases Working

Diagnosing a Water Heater Failure: What to Do When It Ceases Working

Blog Article

Call Today

We have stumbled on this post on Hot Water Heater Repair listed below on the net and believe it made good sense to discuss it with you on this site.


How to Troubleshoot and Repair an Electric Water Heater
Several contemporary homes utilize an electric hot water heater for their heating unit, because of its comfort and also simplicity of use. Nevertheless, just like any other electrical devices, issues may develop with its usage, suddenly. It can be actually frustrating to get up to a chilly shower as opposed to a warm one or having your bath with water that isn't hot enough or perhaps as well hot. Whatever the situation may be, water heater problems can be rather stressful. Thankfully, we have actually made a list of possible solutions to your water heater problems. There are a number of factors that can trigger much of these issues, it could be an issue with the power supply, the electric heating element, or the thermostat. Before doing anything, ensure you shut off the major power supply for safety. Whatever the problem is, getting it fixed should not pose too much of a problem if you follow these actions:

Examine Your Power Supply:


As standard as this might appear, it is very needed. Without adequate power, your hot water heater will not work. So the first thing to do when your water all of a sudden stops working is to verify that it isn't a power problem. Examine if the fuse is blown out or the circuit breaker stumbled. If the breaker is the problem, merely transform it off and on again. Replace any damaged or worn-out fuse. Test the home appliance with power after these modifications to see if it's now functioning.

Check the Burner in the Water Heater:


If it's not a power trouble, after that try having a look at your heating element if it is still functioning. Test each of your heating elements to make sure the problem isn't with any of them. If any one of them is damaged, replace that part and after that check whether the warm water is back on.

Check Your Thermostat:


If your water heater still isn't functioning or the water appearing isn't warm enough, you might require to check the temperature level setups on your upper thermostat. Ensure the circuit breaker is turned off prior to doing anything. Open up the access panel and also press the red button for temperature reset above the thermostat. This need to assist heat the water. Transform the circuit breaker back on and also check if the issue has actually been fixed.

Call A Professional:


If after replacing all malfunctioning components and resetting your temperature, the water heater still isn't working, you might need to speak to a professional plumber for a professional viewpoint. The issue with your heating system could be that the cold and hot taps have actually been switched over or it may be undersized for the quantity of warm water required in your home. Whatever the situation might be, a specialist plumber would certainly assist fix the problem.

Verdict


Hot water heater problems are not always significant. Most of them are because of minor problems like a blown fuse or worn-out heating element. Replacing the defective parts need to work. Nevertheless, if you are still unable to address the trouble, give a call to your nearest plumber ahead to get it fixed.

8 possible reasons why you have no Hot Water


Along with streaming Netflix and having light flood a room when we flick a switch, having hot water flow from our taps and showerheads whenever we want is an oft-overlooked modern miracle of homeownership. That's why, when that flow goes cold, it can be shocking — and not just in a "Wow, that's freezing" kind of way while you're in the shower.


Water Leak


Before hot water reaches your taps and showerheads, it needs to spend some time in your water heater. This appliance, which can be either gas- or electric-powered, takes the cold water that enters your home from your well or utility company and cooks it until it gets hot. It's akin to an electric tea kettle.



Obviously, if your water heater is leaking, it will never fill with water so it won't have anything to warm. To see if this is the case, simply examine the area around the water heater to see if it is wet. If so, you'll likely need to replace the unit, but you can also call in a pro for a second opinion and to see if it is fixable. Sometimes leaks can happen around fixtures on the water heater, and if so, the solution might be as simple as replacing them.


Gas Heater: Gas Leak


If your hot water is fueled by natural gas and there is a leak in the supply line or where the line enters the tank, the appliance won't have the power it needs to heat up your water. The result is not only inconvenient, but it can be extremely dangerous as well. If you smell gas when you investigate your water heater, call your gas utility company immediately and report it as an emergency. It might also be prudent to leave your home until a repair person from the company arrives. Your utility company will usually fix any kind of gas leak. However, in terms of getting your water heater working again, you'll need to relight the pilot and wait a while to see if it is functioning properly. You can call in a water heater specialist or plumber to help with this.


Gas Heater: Pilot Light Problems


There are two other issues with gas-powered water heaters that can lead to a loss of hot water. The first is a pilot light that's blown out. The pilot light is the source of a constant flame inside your water heater. When the heater determines the need to heat up the water it is holding, it will open a valve that will cause gas to flow over the pilot light and cause it to ignite. To see if your pilot light is functioning, there is usually a small window in the front of the water heater. If you can't see a flame, remove the access panel and see if that helps you locate it. If there is still no flame, you'll need to relight it in accordance with the manufacturer's instructions.



Your pilot light should burn with a bright blue flame. If not, make sure there are no drafts affecting it, which could keep it from functioning properly. If the flame looks yellow, it might be a sign of the presence of carbon monoxide, which spells trouble and needs to be looked at right away by a technician.


Gas Heater: Faulty Thermocouple


The second reason why a gas-powered water heater might fail is a faulty thermocouple. This is a small probe that should sit in the pilot light flame. Its purpose is to stop the flow of gas if it senses that the pilot light is out. Sometimes, these probes get knocked off track, so make sure it is directly in the flame. They can also get a buildup on them that prevents their function, so try cleaning yours off with some steel wool or fine-grit sandpaper. If your pilot light won't stay lit and you've tried these steps to fix the thermocouple, it is likely faulty and needs to be replaced. Call a technician.


Electric Heater: Breaker Blues


Electric water heaters don't have pilot lights, because there is no gas to burn in order to heat up the water. Instead, they do their magic through the use of (naturally) electricity. But that's not to say things can't go wrong with them. If your electric water heater isn't working properly, there's a good chance that a breaker was tripped that supplies the appliance power. Check your breaker box and flip any breakers that have switched to the off position back on. If it trips again, then there might be a fault in the water heater, and you'll want to call in a pro to have a look.


Electric Heater: Reaching The Limit


If the breaker is fine, check to see if the high-temperature limit has switched off on the water heater itself. To do so, first turn off the breaker to the unit. Then remove the service panel and press the red button you'll find there. This is the limit switch, and resetting it could solve your problem. To check, replace the panel, turn the breaker back on and listen to see if the water heater is functioning again.


Electric Heater: Heating Element


If these steps don't fix the issue, then you might have a failed heating element, which will need to be replaced. Unless you are comfortable with such repairs, calling in a technician might make the most sense.

https://www.homeserve.com/en-us/blog/home-improvement/no-water-heater/


How to Troubleshoot and Repair an Electric Water Heater

We were made aware of that write-up on Hot Water Heater Repair from an acquaintance on our other web page. Enjoyed reading our article? Please share it. Let other people discover it. Thank you for going through it.


For best results, ring!

Report this page